0800 840 8201

Harmony Internal Wood Stain Range

 

The Harmony internal wood stain range consists of 30 classic colour stains and 20 contemporary pastel colour stains providing expert results to all styles of interior wooden surfaces. We are also able to colour match to get you exactly the colour you need through our ‘Speed Tinting‘ service.

The Harmony range will enhance internal wood’s natural grain and appearance and will have a resistance to UV light, safeguarding the longevity and stability of your colours over time. The Harmony wood stains accentuate the grain in both Hardwood and Softwood. It can be applied using a number of systems such as Spray, Wipe, Brush, Dip and Sponge.

Symphony Coatings supply everything you need for a great looking finish every time. From sanding sealers to clear finishing coats such as Acid Cat, Precat, Polyurethane, Acrylic, Polyester, UV, water based and parquet flooring lacquer. With our wide colour selection, you can create unique looks or match existing wood tones with a formula that’s guaranteed to provide great colour consistency across a variety of different woods.

R

Enhancing Wood

The Harmony internal wood stain range enhances hard and soft wood’s natural grain and appearance, providing resistance to UV light and safeguarding the longevity and stability of your colours.

Your Colour

The Harmony Stain has a set range of 32 classic colours and 18 contemporary pastel colours to suit most needs. We also provide a colour matching service to get you the exact colour you need.

European Excellence

The Harmony internal stain range is made in cooperation with Sopur, a leading European manufacturer of wood stains and patinas that are trusted for their high quality and performance.

Harmony Wood Internal Wood Stain Range

 

*Colours below are to be used as an indication only.

Harmony Wood Stain Range

Request a Harmony Stain Colour Chart

 

Wood Stain Preparation Guide

Ensure that all surfaces are clean, dry and free from surface dirt, debris and sanding dust. Wooden surfaces should be vacuumed or wiped down after sanding to remove surface contaminates prior to applying Harmony stains.

Before using the wood stain, it should be thoroughly mixed. Shaking the container will ensure possible residue at the bottom is dissolved. Ensure you check the colour by conducting a test area. It’s advisable to also try subsequent coats of the final lacquer on top to ensure the finished colour is suitable.  Variable substrates can change the appearance of the Harmony stain. Approve the wood stain colours on the substrate being used before beginning any project.

Technical Guide

The Harmony Wood Stain coverage is approximately 8-12 square meters per litre dependent upon application method the size, alignment and surface quality of the item being coated. Harmony stains will dry within 10 minutes, however drying times may vary depending on room temperature and humidity. Please be aware that due to the nature and make up of our Pastel Colours that to retain Colour Retention Symphony Coatings recommend the over coating lacquer to be a Non-Yellowing type, ask our Technical Department for advice.

Wood Stain Application Guide

The surface should be pre-sanded with 150 – 220 Grit abrasive (depending on the kind of wood) prior to using to avoid problems such as uneven or patchy drying. 1 or 2 coats of Harmony stain can be applied to achieve the desired coverage and colour depth. The best results are achieved between 18℃ and 22℃ with good air movement and ventilation.

When Rag Wiping, use a soft, white, lint-free cloth. (Coloured or printed rags can bleed and cause discolouration). Apply the stain wet to the entire surface to avoid uneven dispersion and then remove any excess with a clean cloth. For bigger surfaces it may be suitable to apply the wood stain in sections. Always work along the grain when wiping off, and leave a minimum of 10 minutes to dry before applying finishing coats.

When Spraying, apply an even wet coat of Harmony stain and remove excess with a soft, white, lint-free cloth. When dry spraying ensure an even coat is applied and that the gun strokes follow the grain of the timber. Wiping can enhance the constancy of the colour and accentuate the grain definition and the natural properties of the wood.

Dipping can be controlled through submerging and wiping the excess stain off with a clean, white, lint-free cloth to achieve an even stain.